Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Garage Door Repair Cost in Winston-Salem?
Garage door repair in Winston-Salem typically costs $150 – $600, with most jobs landing somewhere near the middle of that range. A snapped spring runs $180 – $340 for one spring, while a straightening job on a bent track can come in as low as $120 – $240. The number you’ll actually pay depends on the part, the brand, and how much of the door system has to come apart to reach it.
We know that a garage door that won’t open isn’t a small problem. If the door is stuck down, your car is blocked. If it’s stuck up, your house is open. We work on the brand you already have, from the opener motor down to the bottom seal, so you’re not calling a second company for a second part of the same door. Call (877) 692-2814. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Typical Winston-Salem garage door repair runs $150 – $600, and the written estimate sets the final price.
- Springs are the most common repair: $180 – $340 for one spring, and a matched pair costs about twice that because both are nearly always replaced together.
- Opener problems fall in the $120 – $320 range for repair and $250 – $550 for a full replacement install.
- Estimates are free, and our technicians have up to 9 years of experience.
- We service LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor equipment throughout Winston-Salem.
Garage Door Repair Cost Breakdown (2026)
Here are the typical estimated ranges we see across Winston-Salem for common garage door work. These are estimates to help you plan; the written quote you receive determines the actual price for your door.
| Repair Type | Typical Estimated Range | What It Usually Covers |
|---|---|---|
| Garage door repair (general) | $150 – $600 | The full spread of common fixes, from a single part swap to a multi-point repair |
| Spring repair | $180 – $340 (one spring) | Torsion or extension spring replacement; a matched pair costs about twice this |
| Cable repair | $130 – $250 | Frayed, snapped, or slipped lift cables and the drum hardware they ride on |
| Opener repair | $120 – $320 | Motor, logic board, gear, capacitor, safety sensor, or remote troubleshooting |
| Opener installation | $250 – $550 | New opener and rail install, wired or belt drive, plus safety sensor setup |
| Panel replacement | $250 – $500 | Replacing dented or damaged sections on a sectional door |
| Track realignment | $120 – $240 | Resetting bent or knocked-out vertical and horizontal tracks |
| Roller replacement | $110 – $220 | New nylon or steel rollers, often all at once for smoother travel |
| New door installation | $700 – $2200 | Full replacement door and hardware, sized and fitted for the opening |
What pushes a job toward the top of a range? Two things, mostly: how much of the door has to come down, and how deep the diagnosis goes. A roller swap is quick and stays near $110 – $220. A spring job means releasing tension on a loaded system, which takes time and care, so it sits at $180 – $340 per spring. Opener repair can climb to $320 when the logic board or motor has failed rather than a sensor or remote. If a door has been run for a while with a bent track or a bad cable, several parts often need attention at once, and the total lands higher in the $150 – $600 window. If you’re trying to place a repair like this, our garage door repair page walks through how we approach a diagnosis.
What Affects Garage Door Repair Pricing in Winston-Salem
Winston-Salem doors take a specific kind of wear. Summers here are hot and humid, and winters swing cold and damp. That cycle works on wood frames, metal tracks, and the grease in every moving part, and it’s one reason spring and cable calls show up so often in this market. Here’s what moves the price up or down:
- Which part failed and how many. A single roller or a sensor is a small job. A spring plus a cable plus a bent track is a bigger one, and the combined total climbs into the upper half of the $150 – $600 repair range. We tell you what we find before anything is replaced.
- Door and opener brand. Crescent Garage Door Repair is trained on LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. Familiarity with the system means faster diagnosis, fewer surprises on parts, and less time spent figuring out how a particular opener logic board wants to be tested.
- Door size and material. A single-car steel door and a wide double-car wood door are different jobs, and the same repair can sit at opposite ends of a range. Heavier doors need heavier springs, and that affects the spring cost directly.
- Age and wear on the surrounding hardware. On an older door in Winston-Salem, a failed spring often sits next to a frayed cable and worn rollers. Replacing them together usually costs less than three separate visits and keeps the door from failing again in a month.
- Repair vs. replace. A dented lower panel at $250 – $500 can be replaced on its own. A door with widespread rot, cracked panels, and stressed hardware can reach a point where a new door at $700 – $2200 makes more sense. We’ll tell you which side of that line your door is on.
- Safety and access. A door stuck partway open or closed under tension is a slower, more careful job. We never rush a loaded spring system, and that care is built into the estimate, not added afterward.
How Much Does an Opener Repair Cost in Winston-Salem?
Opener repair in Winston-Salem typically runs $120 – $320, and a full opener replacement install runs $250 – $550. Opener work is the most common call we get, because the opener is the most failure-prone part of the whole system: it carries the electronics, the motor, the gearing, and the safety sensors, and any one of them can stop the door cold.
We treat opener repair as its own specialty, not an afterthought. Whether your opener is a LiftMaster or a Genie, our technicians know the system and test it part by part: the motor, the drive gear, the logic board, the capacitors, the travel limits, and the safety sensors that keep the door from closing on something. If the repair is straightforward, it stays low in the range. If the board or motor has failed, it moves toward $320. Call (877) 692-2814 and we’ll talk through what your opener is doing. Estimates are free.
How Much Does Spring Replacement Cost in Winston-Salem?
Spring replacement in Winston-Salem costs $180 – $340 for one spring. Most residential doors carry a matched pair, and because the two springs are almost always replaced together, a pair costs about twice that range. Springs are rated for a set number of open and close cycles, so once one breaks, the other is usually close behind, and replacing both at once is the sound choice.
We want to be direct about safety here, because springs are the one part of a garage door that genuinely injure people. A torsion spring holds serious stored tension, and a snapped or improperly released spring can strike hard enough to cause real harm. Cables and springs should only be handled by a trained technician with the right tools. Please don’t try to loosen, adjust, or remove a spring yourself. If you’re hearing a loud bang from the garage or the door suddenly feels too heavy to lift, stop using it and call us at (877) 692-2814. We answer 24/7, and we’ll book a visit in the next open dispatch window, Sunday through Friday, 7am to 7pm.
How Much Does Cable Repair Cost in Winston-Salem?
Cable repair in Winston-Salem usually costs $130 – $250. Lift cables fray, snap, or slip off the drum, and when they do, the door often hangs crooked or won’t move at all. Like springs, cables sit under tension, so this is another repair that belongs with a trained technician rather than a weekend project. If a cable has snapped and the door has dropped, don’t run the opener. The motor will fight a door that’s already out of balance. Call us, and we’ll get it inspected and priced. The estimate is free.
How to Save on Garage Door Repair
The best savings come from catching a small problem before it becomes a big one, and from knowing what a job should cost before you agree to it. A few practical things that help in Winston-Salem:
- Start with a free estimate. Our estimates cost nothing and come with a written price, so you know exactly where your job lands in the $150 – $600 range before you commit. Call (877) 692-2814.
- Fix the noise early. A grinding door, a squealing opener, or a door that shudders on the way up is telling you a part is wearing out. Repairing one worn roller at $110 – $220 beats replacing a cable or a spring later.
- Ask about a full inspection while we’re there. If a technician is already out for an opener repair, having the springs, cables, rollers, and track checked in the same visit often catches a second issue before it fails. One visit for two problems is cheaper than two separate calls.
- Don’t push a failing door. Running a door with a snapped spring or a bad cable strains the opener motor, which can turn a $180 – $340 spring job into a combined spring-and-opener bill. Stop using the door when it stops behaving.
- Get the timing of the diagnosis right. If you can describe the symptom clearly – the door won’t close, the door won’t open, the opener just clicks, the lights flash – the technician arrives closer to the answer, which keeps the visit focused and the bill lower.
One more thing worth knowing: no single repair type is “always expensive” or “always cheap.” A panel replacement at $250 – $500 might be the whole bill on one door and a small line on another. That’s why the written estimate matters more than any ballpark. Call us, describe the problem, and we’ll give you a real number for your door. If you’re weighing a repair against a full replacement, you can learn more about how we handle each system, from the opener down to the bottom seal, at Crescent Garage Door Repair.
FAQs – Garage Door Repair Cost
How much does garage door repair cost in Winston-Salem?
Garage door repair in Winston-Salem typically costs $150 – $600. Within that range, a spring replacement runs $180 – $340 for one spring, a cable repair $130 – $250, track realignment $120 – $240, and roller replacement $110 – $220. The written estimate for your specific door sets the final price. Call (877) 692-2814 for a free estimate.
Is it cheaper to repair or replace a garage door?
Repair is almost always cheaper unless the door has widespread damage. A single panel can be replaced for $250 – $500, and a spring or cable fix stays under $340. A new door installation runs $700 – $2200, which is the direction to go when panels are cracked across the door, the frame is failing, or several parts need replacing at once. We’ll give you a straight answer on which makes sense for your door. Call (877) 692-2814 and we’ll walk through it with you.
How much does it cost to replace garage door springs in Winston-Salem?
Spring replacement in Winston-Salem costs $180 – $340 for one spring, and a matched pair is about twice that because both are nearly always changed together. That’s an important detail most quotes don’t spell out, and it’s worth asking about before the work begins. Springs hold dangerous stored tension, so this is a job for a trained technician. Call (877) 692-2814 for an exact quote on your door.
How much does an opener repair cost in Winston-Salem?
Opener repair in Winston-Salem runs $120 – $320, and a full opener replacement install runs $250 – $550. The price within that range depends on the fault: a sensor or remote is a quick, low-cost fix, while a failed logic board or motor moves toward the top. We work on LiftMaster, Chamberlain, Genie, Craftsman, and the other major brands already on Winston-Salem doors. Call (877) 692-2814, and we’ll diagnose it and give you a written price.
Can you come today for a garage door repair in Winston-Salem?
In most cases, yes. We offer same-day service and fast dispatch from 7am to 7pm, Sunday through Friday. Call (877) 692-2814. We answer 24/7, and a call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
Why does a garage door repair cost more on some doors than others?
Because a repair price tracks the parts and labor a specific door needs. A heavier wood door needs heavier springs, which cost more than springs for a light single-car steel door. An older door in Winston-Salem that has run for years on worn rollers and a stretched cable often needs several parts replaced, which pushes the total toward $600. A single sensor or roller fix stays near $110 – $220. The written estimate accounts for your door, not an average. Call (877) 692-2814 for a free estimate on yours.
What Happens When You Call
A quick call is the fastest way to a real number. When you reach us, we’ll ask what the door is doing and which brand is on it, so the right technician gets dispatched with the right knowledge. We cover every brand in the same visit, so whether it’s a Genie opener that won’t run or a Clopay door with a broken spring, you’re calling one company for the whole system. Estimates are free, pricing is upfront, and our technicians have up to 9 years of experience.
Call (877) 692-2814. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Winston-Salem market as of 2026. Crescent Garage Door Repair offers free estimates – call (877) 692-2814.
Written by the team at Crescent Garage Door Repair.
What Our Customers Say
"The old chain drive sounded like a freight train through the bedroom above the garage. Went with the belt drive they recommended and now I genuinely cannot hear it open from upstairs."
- Lisa Ackerman"Door installed in about four hours, old one hauled away, and he stayed to program both cars and the wall panel before he left."
- Tim Novak"Keypad stopped working, which I assumed meant a whole new system. It was the batteries and a reprogram. He charged me the minimum service call and told me how to do it myself next time."
- Michael Meyer