Garage Door Repair in Winston-Salem, NC | Crescent Garage Door Repair

Garage Door Repair in Winston-Salem - On-Site in 60 Minutes, Fixed the Same Day

Most garage door faults are fixed in a single visit. The common springs, cables and rollers are brought to the job, and you get the price before any work starts.

We answer 24/7

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Raised-panel steelRaised-panel steel
Carriage houseCarriage house
Modern flushModern flush
Full-view glassFull-view glass
LiftMaster openersLiftMaster openers
Chamberlain openersChamberlain openers
Every visit starts with

Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included

We have financing partners for your new garage door

You get a price before we start. It does not change when the pro arrives.

Get your free estimate

Trusted Garage Door Repair for Winston-Salem Homeowners

A garage door that won’t open isn’t just an annoyance – it disrupts your whole day. It blocks the car, leaves the house unsecured, and turns a quick errand into a problem you have to solve before anything else. That’s the call we get most, and it’s the one we’re built to handle. Our technicians have up to 9 years of experience working on the door systems and openers already installed in Winston-Salem homes, from older Craftsman openers to newer LiftMaster and Chamberlain units. Whether you’re dealing with a snapped spring, a door that reverses halfway down, or a commercial bay door that’s stuck open, we diagnose the actual failure before we quote anything. We answer 24/7 and offer fast dispatch from 7am to 7pm, Sunday through Friday, so same-day repair is often possible. Call (877) 692-2814 and we’ll get someone out to look at it.

Call (877) 692-2814

As a Crescent Garage Door Repair, we handle the whole system – springs, cables, panels, rollers, tracks, and the opener that drives it all. No handoffs between companies, no second contractor for the motor. If your neighbor in Ardmore or Sherwood Forest mentioned a garage door repair company they liked, you’re still welcome to compare quotes. Free estimates, upfront pricing, and nothing starts until you approve the written number.

Key Takeaways

  • Typical garage door repair in Winston-Salem runs $150-$600, depending on the part and the job.
  • Springs, cables, and torsion hardware are the most common failures and the most dangerous to touch – call a technician.
  • Same-day repair is often available with fast dispatch from 7am to 7pm, Sunday through Friday.
  • Every price is quoted and agreed in writing before any work starts.
  • We service the brand you already have – LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor.

Garage Door Spring Repair

Garage Door Spring Repair is the service we run most often in Winston-Salem, because springs are the part designed to do the heavy lifting – and the first to fail. A torsion spring typically lasts through a set number of open-and-close cycles, and once it reaches that limit it snaps, leaving the door too heavy to lift by hand. You’ll hear a sharp bang, the opener will strain and stall, and the door won’t budge. That’s a spring problem, and it needs a trained technician. Springs are under extreme tension, and adjusting or replacing them without proper tools can cause serious injury. Our technicians replace torsion and extension springs on Clopay, Amarr, and Wayne Dalton doors, match the spring to the door’s weight, and check cable tension and drum alignment while they’re in there. Replacing one spring typically costs $180-$340. A matched pair is usually replaced together, so a pair runs about twice that. The written estimate sets the final price.

Why Springs Break

Springs fail from cycle count, not calendar age, so a door used heavily wears out faster than one opened once a day. North Carolina humidity also speeds corrosion on older steel springs, which weakens them over time. If your door suddenly feels heavy or the opener struggles, stop using it and have it checked.

Single vs. Matched Pair

When one spring breaks, the other has usually lived the same life and is close behind it. We’ll always tell you the condition of both before we quote. Replacing them as a pair saves a second service call down the road.

Explore

Styles & brands we work with

  • Raised-panel steel
  • Carriage house
  • Modern flush
  • Full-view glass
  • LiftMaster openers
  • Chamberlain openers

Garage Door Sensor Repair

Garage Door Sensor Repair fixes the small safety eyes near the floor that tell the opener to stop or reverse when something is in the way. When they’re misaligned, dirty, or wired wrong, the door closes a few inches and shoots back up – or refuses to close at all. It’s one of the most common reasons a Winston-Salem homeowner calls us thinking the opener is dead when the motor is fine. We test the sensor beam, check the wiring back to the opener, realign the brackets, and confirm the door reverses properly under load before we leave. Sensor repair usually falls within the standard repair range of $150-$600, with the exact number based on what’s actually wrong. On most jobs that means a realignment or a replacement sensor, quoted and agreed before we touch anything.

Common Sensor Failures

Sun glare, spider webs, and a bumped bracket account for most sensor calls. The tiny LED on each eye tells you which side is the problem – one solid, one blinking usually means misalignment. If both are dark, it’s likely wiring or power.

When Replacement Makes Sense

Older sensors on Craftsman and Genie openers sometimes fail internally and can’t be repaired. We’ll test before we replace, and we’ll match the new sensor to your existing opener so you don’t pay for a full unit you don’t need.

Emergency Garage Door Repair

Emergency Garage Door Repair is for the failures that can’t wait – a door stuck open overnight, a vehicle trapped inside, a cable that’s come off the drum and left the door hanging crooked. These aren’t cosmetic problems. An open door leaves your home exposed, and a door hung up on one side can come down hard. Call (877) 692-2814 and we’ll get a technician scheduled. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed Saturday, so a call that comes in then gets booked into the next opening. Most emergency work lands within the $150-$600 range, with the exact price depending on the failure. If a spring or cable has failed, do not try to lift the door yourself – leave it and let a trained technician handle it.

What Counts as an Emergency

A door stuck open or a car trapped inside is an emergency. So is a door hanging off its track or a cable that’s snapped and whipped loose. A slow, noisy door is annoying but can usually wait for a scheduled visit.

What to Do While You Wait

If the door is stuck open and you can safely do it, pull the manual release only on a door with intact springs – never on one with a broken spring. Keep kids and pets clear of the door and don’t force it. Then call and we’ll talk you through the next step.

Garage Door Panel Replacement

Garage Door Panel Replacement handles the visible damage – a dented lower panel from a backed-in car, a section cracked by impact, or a panel that’s rusted through at the bottom edge. It’s also the right call when a single section is cosmetically ruined but the rest of the door and hardware are sound, because replacing one panel costs far less than a whole new door. We source panels for Clopay, Amarr, and Wayne Dalton doors and match the profile and color as closely as the manufacturer allows. Panel replacement typically runs $250-$500 per section. Availability depends on the door’s make and model, and a free measure confirms exactly what’s needed before you commit. The written estimate sets the final price.

Repair or Replace the Section

A shallow dent in a steel panel can sometimes be straightened, but deep creases and cracked sections can’t be safely repaired. We’ll tell you honestly which side of that line your door is on before you spend anything.

Matching Panels to Your Door

Panel profiles and colors change over the years, so an exact match isn’t always possible on an older door. When a match isn’t available, we’ll show you the closest options so you can decide.

Garage Door Maintenance

Garage Door Maintenance is the tune-up that keeps a working door working – lubrication, balance checks, hardware tightening, and a close look at the parts that wear. It’s worth doing once a year on any door in Winston-Salem, and it’s especially smart before winter, when cold mornings are hardest on springs and rollers. During a visit we lubricate the springs, hinges, and rollers, check the door’s balance with the opener disengaged, test the safety reverse, and tighten the track and hinge bolts that vibration loosens over time. A maintenance visit typically runs within the standard repair range of $150-$600 depending on what’s found. If we spot a part that’s close to failing, we’ll quote it separately and you decide. Nothing is replaced without your approval first.

What a Tune-Up Covers

Lubrication, balance testing, safety-reverse testing, and a hardware inspection are the core of it. Catching a worn roller or a loose hinge early is far cheaper than waiting for it to fail.

How Often to Schedule

Once a year is the usual recommendation for a residential door, and more often if the door gets heavy daily use. A door that’s started to squeal or shudder is overdue.

Garage Door Roller Replacement

Garage Door Roller Replacement swaps out the small wheels that ride in the track, which wear flat, seize up, or crack as they age. Worn rollers are behind most of the grinding, rattling, and jerky travel you hear on an older door, and a seized roller can chew up the track if it’s left alone. We replace rollers on steel, wood, and insulated doors, and check the track and hinges at the same time since they wear together. Roller replacement typically costs $110-$220 for a full set, depending on the roller type and door size. It’s one of the least expensive repairs we do and one of the most noticeable improvements. The written estimate sets the final price before any work begins.

Signs Your Rollers Are Worn

A door that shudders on the way up, rattles loudly, or feels like it’s grinding is usually telling you the rollers are done. Flat spots on the wheels confirm it once the door is up.

Nylon vs. Steel Rollers

Nylon rollers run quieter than steel and are the usual upgrade on a residential door. Steel rollers last longer under heavy use but are noisier. We’ll recommend based on how your door is used.

Commercial Garage Door Repair

Commercial Garage Door Repair covers the roll-up and sectional doors on shops, warehouses, and loading bays, where a stuck door stops business rather than just inconveniencing a homeowner. Commercial doors take far more cycles than residential ones, so springs, cables, and operators wear out faster and fail under load. We service commercial doors and the openers that drive them, diagnose the failure on site, and give you a written price before any work starts. Typical commercial repair falls within the $150-$600 range for standard fixes, with larger or high-cycle doors quoted individually after we see the door. If a bay is stuck open, call (877) 692-2814 – we answer 24/7 and dispatch from 7am to 7pm, Sunday through Friday.

High-Cycle Door Wear

A commercial door that cycles dozens of times a day burns through springs and rollers far faster than a home door. High-cycle spring options are worth discussing when a door is repaired often.

Operator and Control Issues

Commercial operators and their safety edges fail in ways residential openers don’t. We test the controls and safety devices as part of the repair so the door doesn’t fail again the next morning.

Garage Door Cable Repair

Garage Door Cable Repair handles the steel lift cables that run from the bottom corner of the door up to the drums on the torsion shaft. A cable can fray, snap, or jump the drum, and when it does the door drops on one side and hangs crooked. That’s a stop-using-it situation – a door supported by one cable can come down hard, so don’t run the opener and don’t try to lift it. Our technicians replace both cables as a matched set on most doors, since a cable that’s failed usually means its partner is close behind, and we check the drums and springs while the door is down. Cable repair typically runs $130-$250. The written estimate sets the final price, and nothing starts until you approve it.

How Cables Fail

Cables fray where they wind around the drum and corrode where moisture collects. A few broken strands are the warning – a full snap is what follows if it’s ignored.

Why Cables Come in Pairs

Both cables on a door have lived the same life, so replacing one and leaving the other is a short-term fix. A matched pair keeps the door level and saves a second call.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Brands We Service

We work on the brand you already have, which is a big part of why homeowners call us instead of a single-brand dealer. Clopay doors are common across Winston-Salem, and we know where their panels and hardware wear – especially the bottom sections that take the most moisture. Amarr and Wayne Dalton doors show up on plenty of newer builds, and we’re familiar with how their spring and track systems are set up so we’re not guessing on a repair. On the opener side, LiftMaster and Chamberlain units dominate, and we know their logic boards, safety sensors, and drive gears well enough to diagnose rather than just swap parts. Genie and Craftsman openers have their own quirks, and Raynor doors round out the systems we handle.

Whether you have a Clopay sectional, an Amarr insulated door, a Wayne Dalton with its own torsion setup, or a Craftsman opener that’s been humming along for years, we can help. You don’t need to know the model number before you call – we’ll identify it on site. If you’d rather start with a related visit, we also handle garage door repair for opener problems and full garage door repair for new installations when a door is past saving.

Signs You Need a Pro Right Now

  • A loud bang from the garage. That’s usually a torsion spring snapping. The door will feel extremely heavy and the opener may stall – stop using it and call. Springs are under dangerous tension and shouldn’t be touched without proper tools.
  • The door reverses before it closes. This is the safety sensor doing its job, but a door that won’t close leaves your home open. It’s often a simple realignment, but it needs a technician to confirm the sensor and wiring.
  • A door hanging crooked or off its track. One side dropping means a cable or roller has failed. Forcing the opener can bend the track and turn a small repair into a bigger one. Leave it down and call.
  • Grinding, squealing, or shuddering on the way up. Worn rollers or dry hinges are the usual cause. It’s a cheap fix now and a track replacement later if it’s ignored.
  • The opener runs but the door doesn’t move. Could be a stripped gear, a broken spring, or a released manual lock. A technician can tell which in a few minutes and quote the right repair instead of a new opener.

Our Process, Step by Step

  1. 1
    You call and describe the problem. We’ll ask what the door is doing and which brand it is, so we can bring the right parts and knowledge. Call (877) 692-2814 – we answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
  2. 2
    We diagnose on site. Our technician tests the door by hand with the opener disengaged, checks spring tension, cable condition, roller wear, and the opener’s safety reverse. That’s how we find the actual failure instead of guessing.
  3. 3
    You get a written estimate. We explain what’s wrong, what it costs, and what happens if it’s left alone. The price is quoted and agreed before any work starts – no surprises when the job is done.
  4. 4
    We do the repair. Springs, cables, rollers, panels, sensors, or the opener – we handle the whole system in one visit where the parts allow. Brand-agnostic, so we fix what’s there rather than pushing a replacement.
  5. 5
    We test the door and walk you through it. Balance, safety reverse, and a full open-and-close cycle before we leave. If something needs watching, we’ll tell you so you’re not caught off guard.

How Much Does Garage Door Repair Cost in Winston-Salem?

Garage door repair in Winston-Salem typically runs $150-$600, and the final number depends on which part failed and how much of the system it took with it. A single spring replacement is usually $180-$340, while a matched pair costs about twice that because both springs are replaced together. Cable repair runs $130-$250. Roller replacement is the least expensive common fix at $110-$220. Panel replacement for a damaged section is $250-$500. Sensor repair usually sits on the lower end of the $150-$600 range since it’s often a realignment. Opener repair, when the motor itself is the problem, runs $120-$320, and a full opener installation is $250-$550.

What moves the price is the part itself, the door size and weight, whether the failure damaged the track or cables, and whether the door is an older model that needs a matched component. The best way to avoid overpaying is to get a written estimate before work starts and ask what’s included – parts, labor, and testing. Our free estimate covers the diagnosis, a clear explanation, and the exact price in writing. The written estimate sets the final price, and nothing gets added after the fact.

Our Service Area Near Winston-Salem

We serve homeowners and businesses across Winston-Salem and the surrounding towns, including Clemmons, Rural Hall, Midway, Lewisville, Tobaccoville, Bermuda Run, King, Welcome, Lexington, Mocksville, and Tyro. Response times depend on where you are and how the day is running, but fast dispatch from 7am to 7pm, Sunday through Friday, means most calls get a technician out the same day. If you’re outside Winston-Salem, call and we’ll confirm the next opening in your area.

Serving Winston-Salem, NC – Our Local Coverage Area

We serve Winston-Salem and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Garage Door Repair in Winston-Salem

Schedule Your Garage Door Repair Service in Winston-Salem Today

A door that won’t close, a spring that snapped, or an opener that’s given up – none of it has to wait. Call (877) 692-2814 and we’ll schedule a technician, diagnose the problem, and give you a written price before any work starts. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Free estimates, upfront pricing, and a satisfaction guarantee on the work we do. One call for the whole door.

Written by the team at Crescent Garage Door Repair.

Why Winston-Salem Chooses Crescent Garage Door Repair

We set the standard for garage door repair in Winston-Salem.

30-60 Min Response

Fast dispatch across Winston-Salem, 7am-7pm. Same-day service available.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Winston-Salem

Getting your garage door repair handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your garage door repair needs and we provide an upfront, transparent quote with no obligation and no hidden fees.

2

Licensed Technician Dispatched

A background-checked, certified technician arrives in Winston-Salem - typically within 30-60 minutes.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local garage door repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    A background-checked tech heads outLicensed & insured, typically the same day.
  4. 4
    You approve before work beginsNothing starts until you say go.

What Winston-Salem Customers Say

Trusted by homeowners across Winston-Salem and surrounding areas.

★★★★★

"The old chain drive sounded like a freight train through the bedroom above the garage. Went with the belt drive they recommended and now I genuinely cannot hear it open from upstairs."

Lisa Ackerman
★★★★★

"Door installed in about four hours, old one hauled away, and he stayed to program both cars and the wall panel before he left."

Tim Novak
★★★★★

"Keypad stopped working, which I assumed meant a whole new system. It was the batteries and a reprogram. He charged me the minimum service call and told me how to do it myself next time."

Michael Meyer

Ready for Garage Door Repair in Winston-Salem?

Call now for a free estimate, or request one below. Licensed, insured, and here with fast help in Winston-Salem.

(877) 692-2814

Request a Free Estimate in Winston-Salem

Tell us about your garage door repair needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Local Service Coverage
Call Now - We Answer 24/7