Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateTrusted Garage Door Repair for Winston-Salem Homeowners
A garage door that won’t open isn’t just an annoyance – it disrupts your whole day. It blocks the car, leaves the house unsecured, and turns a quick errand into a problem you have to solve before anything else. That’s the call we get most, and it’s the one we’re built to handle. Our technicians have up to 9 years of experience working on the door systems and openers already installed in Winston-Salem homes, from older Craftsman openers to newer LiftMaster and Chamberlain units. Whether you’re dealing with a snapped spring, a door that reverses halfway down, or a commercial bay door that’s stuck open, we diagnose the actual failure before we quote anything. We answer 24/7 and offer fast dispatch from 7am to 7pm, Sunday through Friday, so same-day repair is often possible. Call (877) 692-2814 and we’ll get someone out to look at it.
As a Crescent Garage Door Repair, we handle the whole system – springs, cables, panels, rollers, tracks, and the opener that drives it all. No handoffs between companies, no second contractor for the motor. If your neighbor in Ardmore or Sherwood Forest mentioned a garage door repair company they liked, you’re still welcome to compare quotes. Free estimates, upfront pricing, and nothing starts until you approve the written number.
Key Takeaways
- Typical garage door repair in Winston-Salem runs $150-$600, depending on the part and the job.
- Springs, cables, and torsion hardware are the most common failures and the most dangerous to touch – call a technician.
- Same-day repair is often available with fast dispatch from 7am to 7pm, Sunday through Friday.
- Every price is quoted and agreed in writing before any work starts.
- We service the brand you already have – LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor.
Garage Door Spring Repair
Garage Door Spring Repair is the service we run most often in Winston-Salem, because springs are the part designed to do the heavy lifting – and the first to fail. A torsion spring typically lasts through a set number of open-and-close cycles, and once it reaches that limit it snaps, leaving the door too heavy to lift by hand. You’ll hear a sharp bang, the opener will strain and stall, and the door won’t budge. That’s a spring problem, and it needs a trained technician. Springs are under extreme tension, and adjusting or replacing them without proper tools can cause serious injury. Our technicians replace torsion and extension springs on Clopay, Amarr, and Wayne Dalton doors, match the spring to the door’s weight, and check cable tension and drum alignment while they’re in there. Replacing one spring typically costs $180-$340. A matched pair is usually replaced together, so a pair runs about twice that. The written estimate sets the final price.
Why Springs Break
Springs fail from cycle count, not calendar age, so a door used heavily wears out faster than one opened once a day. North Carolina humidity also speeds corrosion on older steel springs, which weakens them over time. If your door suddenly feels heavy or the opener struggles, stop using it and have it checked.
Single vs. Matched Pair
When one spring breaks, the other has usually lived the same life and is close behind it. We’ll always tell you the condition of both before we quote. Replacing them as a pair saves a second service call down the road.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Garage Door Sensor Repair
Garage Door Sensor Repair fixes the small safety eyes near the floor that tell the opener to stop or reverse when something is in the way. When they’re misaligned, dirty, or wired wrong, the door closes a few inches and shoots back up – or refuses to close at all. It’s one of the most common reasons a Winston-Salem homeowner calls us thinking the opener is dead when the motor is fine. We test the sensor beam, check the wiring back to the opener, realign the brackets, and confirm the door reverses properly under load before we leave. Sensor repair usually falls within the standard repair range of $150-$600, with the exact number based on what’s actually wrong. On most jobs that means a realignment or a replacement sensor, quoted and agreed before we touch anything.
Common Sensor Failures
Sun glare, spider webs, and a bumped bracket account for most sensor calls. The tiny LED on each eye tells you which side is the problem – one solid, one blinking usually means misalignment. If both are dark, it’s likely wiring or power.
When Replacement Makes Sense
Older sensors on Craftsman and Genie openers sometimes fail internally and can’t be repaired. We’ll test before we replace, and we’ll match the new sensor to your existing opener so you don’t pay for a full unit you don’t need.
Emergency Garage Door Repair
Emergency Garage Door Repair is for the failures that can’t wait – a door stuck open overnight, a vehicle trapped inside, a cable that’s come off the drum and left the door hanging crooked. These aren’t cosmetic problems. An open door leaves your home exposed, and a door hung up on one side can come down hard. Call (877) 692-2814 and we’ll get a technician scheduled. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed Saturday, so a call that comes in then gets booked into the next opening. Most emergency work lands within the $150-$600 range, with the exact price depending on the failure. If a spring or cable has failed, do not try to lift the door yourself – leave it and let a trained technician handle it.
What Counts as an Emergency
A door stuck open or a car trapped inside is an emergency. So is a door hanging off its track or a cable that’s snapped and whipped loose. A slow, noisy door is annoying but can usually wait for a scheduled visit.
What to Do While You Wait
If the door is stuck open and you can safely do it, pull the manual release only on a door with intact springs – never on one with a broken spring. Keep kids and pets clear of the door and don’t force it. Then call and we’ll talk you through the next step.
Garage Door Panel Replacement
Garage Door Panel Replacement handles the visible damage – a dented lower panel from a backed-in car, a section cracked by impact, or a panel that’s rusted through at the bottom edge. It’s also the right call when a single section is cosmetically ruined but the rest of the door and hardware are sound, because replacing one panel costs far less than a whole new door. We source panels for Clopay, Amarr, and Wayne Dalton doors and match the profile and color as closely as the manufacturer allows. Panel replacement typically runs $250-$500 per section. Availability depends on the door’s make and model, and a free measure confirms exactly what’s needed before you commit. The written estimate sets the final price.
Repair or Replace the Section
A shallow dent in a steel panel can sometimes be straightened, but deep creases and cracked sections can’t be safely repaired. We’ll tell you honestly which side of that line your door is on before you spend anything.
Matching Panels to Your Door
Panel profiles and colors change over the years, so an exact match isn’t always possible on an older door. When a match isn’t available, we’ll show you the closest options so you can decide.
Garage Door Maintenance
Garage Door Maintenance is the tune-up that keeps a working door working – lubrication, balance checks, hardware tightening, and a close look at the parts that wear. It’s worth doing once a year on any door in Winston-Salem, and it’s especially smart before winter, when cold mornings are hardest on springs and rollers. During a visit we lubricate the springs, hinges, and rollers, check the door’s balance with the opener disengaged, test the safety reverse, and tighten the track and hinge bolts that vibration loosens over time. A maintenance visit typically runs within the standard repair range of $150-$600 depending on what’s found. If we spot a part that’s close to failing, we’ll quote it separately and you decide. Nothing is replaced without your approval first.
What a Tune-Up Covers
Lubrication, balance testing, safety-reverse testing, and a hardware inspection are the core of it. Catching a worn roller or a loose hinge early is far cheaper than waiting for it to fail.
How Often to Schedule
Once a year is the usual recommendation for a residential door, and more often if the door gets heavy daily use. A door that’s started to squeal or shudder is overdue.
Garage Door Roller Replacement
Garage Door Roller Replacement swaps out the small wheels that ride in the track, which wear flat, seize up, or crack as they age. Worn rollers are behind most of the grinding, rattling, and jerky travel you hear on an older door, and a seized roller can chew up the track if it’s left alone. We replace rollers on steel, wood, and insulated doors, and check the track and hinges at the same time since they wear together. Roller replacement typically costs $110-$220 for a full set, depending on the roller type and door size. It’s one of the least expensive repairs we do and one of the most noticeable improvements. The written estimate sets the final price before any work begins.
Signs Your Rollers Are Worn
A door that shudders on the way up, rattles loudly, or feels like it’s grinding is usually telling you the rollers are done. Flat spots on the wheels confirm it once the door is up.
Nylon vs. Steel Rollers
Nylon rollers run quieter than steel and are the usual upgrade on a residential door. Steel rollers last longer under heavy use but are noisier. We’ll recommend based on how your door is used.
Commercial Garage Door Repair
Commercial Garage Door Repair covers the roll-up and sectional doors on shops, warehouses, and loading bays, where a stuck door stops business rather than just inconveniencing a homeowner. Commercial doors take far more cycles than residential ones, so springs, cables, and operators wear out faster and fail under load. We service commercial doors and the openers that drive them, diagnose the failure on site, and give you a written price before any work starts. Typical commercial repair falls within the $150-$600 range for standard fixes, with larger or high-cycle doors quoted individually after we see the door. If a bay is stuck open, call (877) 692-2814 – we answer 24/7 and dispatch from 7am to 7pm, Sunday through Friday.
High-Cycle Door Wear
A commercial door that cycles dozens of times a day burns through springs and rollers far faster than a home door. High-cycle spring options are worth discussing when a door is repaired often.
Operator and Control Issues
Commercial operators and their safety edges fail in ways residential openers don’t. We test the controls and safety devices as part of the repair so the door doesn’t fail again the next morning.
Garage Door Cable Repair
Garage Door Cable Repair handles the steel lift cables that run from the bottom corner of the door up to the drums on the torsion shaft. A cable can fray, snap, or jump the drum, and when it does the door drops on one side and hangs crooked. That’s a stop-using-it situation – a door supported by one cable can come down hard, so don’t run the opener and don’t try to lift it. Our technicians replace both cables as a matched set on most doors, since a cable that’s failed usually means its partner is close behind, and we check the drums and springs while the door is down. Cable repair typically runs $130-$250. The written estimate sets the final price, and nothing starts until you approve it.
How Cables Fail
Cables fray where they wind around the drum and corrode where moisture collects. A few broken strands are the warning – a full snap is what follows if it’s ignored.
Why Cables Come in Pairs
Both cables on a door have lived the same life, so replacing one and leaving the other is a short-term fix. A matched pair keeps the door level and saves a second call.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We work on the brand you already have, which is a big part of why homeowners call us instead of a single-brand dealer. Clopay doors are common across Winston-Salem, and we know where their panels and hardware wear – especially the bottom sections that take the most moisture. Amarr and Wayne Dalton doors show up on plenty of newer builds, and we’re familiar with how their spring and track systems are set up so we’re not guessing on a repair. On the opener side, LiftMaster and Chamberlain units dominate, and we know their logic boards, safety sensors, and drive gears well enough to diagnose rather than just swap parts. Genie and Craftsman openers have their own quirks, and Raynor doors round out the systems we handle.
Whether you have a Clopay sectional, an Amarr insulated door, a Wayne Dalton with its own torsion setup, or a Craftsman opener that’s been humming along for years, we can help. You don’t need to know the model number before you call – we’ll identify it on site. If you’d rather start with a related visit, we also handle garage door repair for opener problems and full garage door repair for new installations when a door is past saving.
Signs You Need a Pro Right Now
- A loud bang from the garage. That’s usually a torsion spring snapping. The door will feel extremely heavy and the opener may stall – stop using it and call. Springs are under dangerous tension and shouldn’t be touched without proper tools.
- The door reverses before it closes. This is the safety sensor doing its job, but a door that won’t close leaves your home open. It’s often a simple realignment, but it needs a technician to confirm the sensor and wiring.
- A door hanging crooked or off its track. One side dropping means a cable or roller has failed. Forcing the opener can bend the track and turn a small repair into a bigger one. Leave it down and call.
- Grinding, squealing, or shuddering on the way up. Worn rollers or dry hinges are the usual cause. It’s a cheap fix now and a track replacement later if it’s ignored.
- The opener runs but the door doesn’t move. Could be a stripped gear, a broken spring, or a released manual lock. A technician can tell which in a few minutes and quote the right repair instead of a new opener.
Our Process, Step by Step
- 1
You call and describe the problem. We’ll ask what the door is doing and which brand it is, so we can bring the right parts and knowledge. Call (877) 692-2814 – we answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
- 2
We diagnose on site. Our technician tests the door by hand with the opener disengaged, checks spring tension, cable condition, roller wear, and the opener’s safety reverse. That’s how we find the actual failure instead of guessing.
- 3
You get a written estimate. We explain what’s wrong, what it costs, and what happens if it’s left alone. The price is quoted and agreed before any work starts – no surprises when the job is done.
- 4
We do the repair. Springs, cables, rollers, panels, sensors, or the opener – we handle the whole system in one visit where the parts allow. Brand-agnostic, so we fix what’s there rather than pushing a replacement.
- 5
We test the door and walk you through it. Balance, safety reverse, and a full open-and-close cycle before we leave. If something needs watching, we’ll tell you so you’re not caught off guard.
How Much Does Garage Door Repair Cost in Winston-Salem?
Garage door repair in Winston-Salem typically runs $150-$600, and the final number depends on which part failed and how much of the system it took with it. A single spring replacement is usually $180-$340, while a matched pair costs about twice that because both springs are replaced together. Cable repair runs $130-$250. Roller replacement is the least expensive common fix at $110-$220. Panel replacement for a damaged section is $250-$500. Sensor repair usually sits on the lower end of the $150-$600 range since it’s often a realignment. Opener repair, when the motor itself is the problem, runs $120-$320, and a full opener installation is $250-$550.
What moves the price is the part itself, the door size and weight, whether the failure damaged the track or cables, and whether the door is an older model that needs a matched component. The best way to avoid overpaying is to get a written estimate before work starts and ask what’s included – parts, labor, and testing. Our free estimate covers the diagnosis, a clear explanation, and the exact price in writing. The written estimate sets the final price, and nothing gets added after the fact.
Our Service Area Near Winston-Salem
We serve homeowners and businesses across Winston-Salem and the surrounding towns, including Clemmons, Rural Hall, Midway, Lewisville, Tobaccoville, Bermuda Run, King, Welcome, Lexington, Mocksville, and Tyro. Response times depend on where you are and how the day is running, but fast dispatch from 7am to 7pm, Sunday through Friday, means most calls get a technician out the same day. If you’re outside Winston-Salem, call and we’ll confirm the next opening in your area.
Serving Winston-Salem, NC – Our Local Coverage Area
We serve Winston-Salem and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Garage Door Repair in Winston-Salem
Garage door repair is fixing the parts of a door system that have failed – springs, cables, rollers, panels, tracks, sensors, or the opener – so the door opens and closes safely again. It covers the door itself and the mechanism that drives it, which is why we handle both in one visit. A repair fixes the specific failure rather than replacing the whole door, and most jobs are done in a single appointment.
Most residential repairs take one to two hours on site, depending on the part. A spring or cable replacement is usually the longer end of that, while sensors and rollers are quicker. If a part has to be ordered, we’ll tell you the timeline up front before scheduling. Call (877) 692-2814 for an exact quote – estimates are free.
Typical garage door repair in Winston-Salem runs $150-$600, with springs at $180-$340 each, cables at $130-$250, rollers at $110-$220, and panel replacement at $250-$500 per section. Opener repair runs $120-$320. The written estimate sets the final price, quoted before any work starts. Call (877) 692-2814 for an exact quote – estimates are free.
Yes. We service Clopay, Amarr, Wayne Dalton, and Craftsman along with LiftMaster, Chamberlain, Genie, and Raynor. Our technicians are familiar with how each brand’s springs, tracks, and openers wear, so we diagnose the actual problem instead of pushing a replacement. Call (877) 692-2814 and tell us the brand – estimates are free.
Same-day repair is often available. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed Saturday, so a call that comes in then is booked into the next opening. Call (877) 692-2814 to check availability for your address.
Yes. We stand behind the repair work we do and the parts we install, and we’ll explain the warranty terms on your specific job before you approve anything. If something isn’t right after the visit, call us and we’ll make it right. Call (877) 692-2814 with any warranty question – estimates are free.
Clear the area in front of and under the door, and move anything stored along the tracks or near the opener. If you can, note when the problem started and whether it’s constant or intermittent. Have your door and opener brand ready if you know it, and make sure someone is home to let the technician in.
Schedule Your Garage Door Repair Service in Winston-Salem Today
A door that won’t close, a spring that snapped, or an opener that’s given up – none of it has to wait. Call (877) 692-2814 and we’ll schedule a technician, diagnose the problem, and give you a written price before any work starts. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Free estimates, upfront pricing, and a satisfaction guarantee on the work we do. One call for the whole door.
Written by the team at Crescent Garage Door Repair.